What's the strangest/hardest question you've been asked on an oral?
#34
Originally Posted by LAfrequentflyer
Appx 10 minutes.
250 an hour, 125 in 30 minutes, 62 in 15 minutes, 31 in 7.5 minutes...
-LAFF
250 an hour, 125 in 30 minutes, 62 in 15 minutes, 31 in 7.5 minutes...
-LAFF
I figured 60kts is one mile a min so it would take 50 min. 120 would be 25 min and 240 would be 12.5 min. I knew I was going 250 not 240 so I just said 12 min. After the interview I figured 50 is one fifth of 250 therefore it would take one fifth of an hour. 60 divided by 5 is 12 miles.
I still did not get the job. (United)
#35
Gets Weekends Off
Joined APC: Jul 2006
Posts: 146
E6-B Ok?
Originally Posted by mike734
I can't believe I pulled that one out but here is how I did it.
I figured 60kts is one mile a min so it would take 50 min. 120 would be 25 min and 240 would be 12.5 min. I knew I was going 250 not 240 so I just said 12 min. After the interview I figured 50 is one fifth of 250 therefore it would take one fifth of an hour. 60 divided by 5 is 12 miles.
I still did not get the job. (United)
I figured 60kts is one mile a min so it would take 50 min. 120 would be 25 min and 240 would be 12.5 min. I knew I was going 250 not 240 so I just said 12 min. After the interview I figured 50 is one fifth of 250 therefore it would take one fifth of an hour. 60 divided by 5 is 12 miles.
I still did not get the job. (United)
ie. 50nm/250kts=0.2hr (12 mins).
How many milli-seconds did they give you to answer that?
If I got asked something like that during an interview I think I'd be itching to check it with the E6-B my wristwatch bezel; though I'm do wonder how well that would go over.
Would that be a major faux pas?
It would be ideal to be able to instantly crunch the numbers during an interview; but we all know how grueling those can be. If, for example you are nearing the end of the interview and you get asked that type of question (which is one that you could normally answer unaided) and you realize that you are starting to get brain fade, would it not be better to utilize the E6-B on your wristwatch and be sure of your answer, rather than not and so give only an approximate, or worse and give an incorrect answer?
If anyone has advice about handling this sort of scenario during an interview (ie. if it's ok/not ok to reference an E6-B) I'm all ears for it.
#36
Not so much a question but direction from the Doc
I'm undressed on the exam table and the Doctor says "Roll over on your left side facing the wall and put your right knee as high on the wall as you can." Delta 1991.
#37
Originally Posted by NZAV8R
How many milli-seconds did they give you to answer that?
If I got asked something like that during an interview I think I'd be itching to check it with the E6-B my wristwatch bezel; though I'm do wonder how well that would go over.
Would that be a major faux pas?
It would be ideal to be able to instantly crunch the numbers during an interview; but we all know how grueling those can be. If, for example you are nearing the end of the interview and you get asked that type of question (which is one that you could normally answer unaided) and you realize that you are starting to get brain fade, would it not be better to utilize the E6-B on your wristwatch and be sure of your answer, rather than not and so give only an approximate, or worse and give an incorrect answer?
If anyone has advice about handling this sort of scenario during an interview (ie. if it's ok/not ok to reference an E6-B) I'm all ears for it.
If I were interviewing I would rather hire the guy who just knows it takes about 10 minutes rather than the guy who gets flustered, refers to his E6-b watch and "calculates" the answer.
A similar question often asked (in the old days) was: Say you need to dump 12000 pounds of fuel. Your aircraft can dump 100 gals a min. How long would it take? Now you could go to your E6-b and figure the density of the fuel for the tank temperature and figure the weight of a gallon. Then you could divide the 12000 pounds by your weight calculation and come up with an answer. I would rather just figure about 6 pounds per gal times 100 gals per hour divided in to 12000 = about 20 mins. Who would you rather hire?
BTW a really experienced 727 Capt. would just say, "I'd get the flight engr. to figure that out!"
Thread
Thread Starter
Forum
Replies
Last Post